Yes, OWOSSO makes brass combination dies that will foil and emboss on one pass.
If you don’t find the answer to your specific question here, please do not hesitate to contact our Customer Service Specialists at OWOSSO by phone at 1-800-444-5552 or by e-mail.
Yes, magnesium is used in model making, candy, casting, and automotive molds just to name a few of the many possible applications.
If you don’t find the answer to your specific question here, please do not hesitate to contact our Customer Service Specialists at OWOSSO by phone at 1-800-444-5552 or by e-mail.
Yes, a 1/4 inch die etched to .100th+ can be used to heat seal.
If you don’t find the answer to your specific question here, please do not hesitate to contact our Customer Service Specialists at OWOSSO by phone at 1-800-444-5552 or by email.
Magnesium can be etched any depth +/- .002th, and can also be etched all the way through the die.
If you don’t find the answer to your specific question here, please do not hesitate to contact our Customer Service Specialists at OWOSSO by phone at 1-800-444-5552 or by e-mail.
The image area of the die can be:
Magnesium:
- 16 gauge — 29″x79″
- 11pt. — 29″x119″
- 1/4″ — 29″x119″
Copper:
- 16 gauge — 17 1/2″ x 23 1/2″
- 1/4″ — 20″ x 26″
If you don’t find the answer to your specific question here, please do not hesitate to contact our Customer Service Specialists at OWOSSO by phone at 1-800-444-5552 or by email.
Yes, OWOSSO can control the slope from the top of the die to bottom of the etch.
If you don’t find the answer to your specific question here, please do not hesitate to contact our Customer Service Specialists at OWOSSO by phone at 1-800-444-5552 or by e-mail.
Yes, a 1/4 inch magnesium die will emboss fabric. However you will need the proper backing to hold the emboss.
If you don’t find the answer to your specific question here, please do not hesitate to contact our Customer Service Specialists at OWOSSO by phone at 1-800-444-5552 or by e-mail.
If you don’t find the answer to your specific question here, please do not hesitate to contact our Customer Service Specialists at OWOSSO by phone at 1-800-444-5552 or by email .
There may be something on surface of die that is preventing the foil from sticking. Try cleaning the die with a fine steel wool or an acetone.
If you don’t find the answer to your specific question here, please do not hesitate to contact our Customer Service Specialists at OWOSSO by phone at 1-800-444-5552 or by e-mail.
A “normal” die is wrong reading so when you stamp or print the finished piece is right reading. On a die that is right reading, you can read the die but when you stamp or print, the image is wrong reading.
If you don’t find the answer to your specific question here, please do not hesitate to contact our Customer Service Specialists at OWOSSO by phone at 1-800-444-5552 or by email .
OWOSSO Release Coating is used on thermal kiss-cut dies to keep the die from sticking and to stop vinyl from building up on the shoulder of the die. It can also be used on foil stamping and debossing dies, and rubber stamp masters.
If you don’t find the answer to your specific question here, please do not hesitate to contact our Customer Service Specialists at OWOSSO by phone at 1-800-444-5552 or by e-mail.
Yes, by using a brass sculptured die you can achieve different levels of embossing.
If you don’t find the answer to your specific question here, please do not hesitate to contact our Customer Service Specialists at OWOSSO by phone at 1-800-444-5552 or by e-mail.
It depends on what type of press is being used. Most Howard or Kwik print presses use magnesium mounted dies, and Kluge or Radio Frequency presses use unmounted dies. For all leather debossing, it is best to use 1/4″ or 3/8″ magnesium.
If you don’t find the answer to your specific question here, please do not hesitate to contact our Customer Service Specialists at OWOSSO by phone at 1-800-444-5552 or by email.